DynaVap Guide: Which DynaVap suits you?
DynaVap Guide 2026: M7 / M7XL, UniDyn, WoodWynd, VonG (i)/(X), HyperDyn & beginner models compared
- Affordable introduction: The G3 – glass body, 0.05 g chamber, lighter included.
- Best entry with upgrade path: The B2 – stainless steel, 0.075 g, fits all DynaVap tips and induction heaters.
- The daily driver: M7 / M7XL – 0.1 g, Adjust-a-Bowl, six airflow levels on the XL.
- Lightest titanium setup: The UniDyn – one-piece UniBody, BallR Cap, only two O-rings.
- For water filters: VonG (i) – solid titanium steel with 10 mm and 14 mm cone.
- Large chamber: HyperDyn – 0.25 g big bowl, Hyper Cap, seven airflow levels.
DynaVap Quickstart: how the “click” works in 60 seconds
- Filling: loosely fill the chamber (do not pack). Depending on the model, this is 0.05 g (G3) to 0.25 g (HyperDyn) – the grind should be medium-fine, not powdery.
- Heating: rotate the cap evenly until the click. The flame should be on the edge of the cap, not in the center – and never on wood or silicone parts.
- Drawing: calm, steady – depending on the model, directly at the mouthpiece or water adapter. Wait 3–5 seconds after the click before drawing: the result will be noticeably smoother.
- Cooldown: only reheat after the second click (cooldown click). Expect two to three heating cycles per fill.
- Milder, more flavorful: heat shorter (remove flame earlier), wait longer after the click, draw slowly.
- Denser, stronger: heat a moment beyond the click and draw faster.
- Airflow: With M7, M7XL, UniDyn, VonG X, and HyperDyn, you also adjust via the airport or condenser depth – tighter = hotter and denser, more open = cooler and milder.
How do you heat the DynaVap? Lighter, torch, or induction
- Single Flame Torch (DynaTorch): Included with The B, The B2, and M7 / M7XL, with a Clipper Torch for the G3. Note: The torches are delivered empty – you need butane separately. This is the cheapest and most portable solution.
- Multi-flame torch: The Starter set The VonG (i) includes a cyclone triple torch. More flames mean: more even and faster to the click, less twisting needed.
- Induction heater: The most reproducible method – you insert the cap and wait for the click, no flame and no wrist technique needed. For WoodWynd, DynaVap explicitly recommends this because no flame touches the wood. Unlike the glass models, the The B2 is also induction-compatible.
- Important exception: For the DynaVap G3, the manufacturer advises against induction heaters like “The Wand” – the glass body is not designed for that. Here, stick with the flame.
1) Beginner & budget: The B, The B2, The G3 (simple, quick start)
DynaVap – The G3: simple, robust, great entry point
The DynaVap G3 Vaporizer is an extremely straightforward entry: minimal fuss, easy to handle, and perfect if you just want to try DynaVap. Use case: at home & on the go, if you want a low-maintenance setup. The special feature: The G3 consists of only two parts – Captive Cap and a glass unibody, where the tip and middle part are made from one piece, including an integrated glass screen.
- Chamber: 0.05 g – the smallest in the lineup, ideal for microdosing.
- Material: Glass unibody with glass chamber and integrated glass screen, plus the Captive Cap.
- Design: Tri-lobe shape with anti-roll function – won’t roll off your table.
- Scope of delivery: G3, Clipper Torch (random color), and DynaVap tin.
- Note: No induction heater, and tips, condensers, as well as dosing capsules from other models do not fit here. The G3 is compatible with Standard Cap, Low Temp Cap, and Perforated Cap.
DynaVap – The B: easy entry with case (everyday setup)
The DynaVap The B is a great “first daily”: straightforward, quick to use, and ideal for DynaVap storage thanks to the case. Use case: if you want a set you can just grab and go – without loose parts flying around. Tip, condenser, and CCD screen are made of medical-grade stainless steel, the stem is food-grade silicone – making it durable and pleasantly grippy.
- Material: stainless steel (tip, condenser, CCD screen) with silicone stem · made in the USA.
- To the click: approx. 5–7 seconds with a single flame.
- Water filter: 10mm cone – fits directly, no adapter needed.
- Includes: The B (captive cap, tip, silicone stem, condenser), metal case, and DynaTorch.
- Extra: 90-day money-back guarantee from DynaVap · upgradable later because parts fit the DynaVap system.
DynaVap – The B2: the upgrade for “more” (with case)
The The B2 is for those who want to start out a bit more “grown-up”: more presence in handling, a clean impression, and a set that looks premium everyday. Use case: if you love the DynaVap principle but want to feel “better equipped” from the start. The key difference from the G3: The B2 is fully expandable – it fits all DynaVap tips and works with induction heaters.
- Chamber: 0.075 g – slightly more than the G3, still clearly in the microdosing range.
- Material: stainless steel (cap, tip, condenser, CCD screen) with high-temperature resistant silicone stem.
- Compatibility: all DynaVap tips, induction heaters like The Wand, SlingStash · 10mm cone for water filters.
- Includes: B2, DynaVap tin, and DynaTorch (empty).
- Design: Anti-roll, grippy silicone stem that turns well when heated.
- G3: cheapest entry, glass body, 0.05 g – but no induction heater and no accessory expansion.
- The B vs B2: Technically very close (stainless steel + silicone stem, 10-mm cone, DynaTorch included). The B2 is the newer design with a 0.075 g chamber and explicit approval for all tips and induction heaters.
- Our recommendation: If you suspect you’ll stick with DynaVap, get the B2 – it grows with you. If you just want to see if you like the principle, the G3 is completely sufficient.
2) The “Sweet Spot” for many: DynaVap M7 & M7XL (with case)
DynaVap – M7: compact, direct, daily-capable
The M7 is our recommendation if you want a “real” DynaVap that you can use every day: sturdy, comfortable in the hand, and a setup that you can keep clean quickly. Use case: Daily driver for short sessions – perfect if you like efficiency. Technically, it features the Finless Tip design, which reduces heat conduction towards the stem by up to 20% – the device stays noticeably cooler in the hand when heating.
- Material: fully stainless steel, textured stem for better grip.
- Chamber: 0.1 g, halved with Adjust-a-Bowl.
- Airflow: Airport design with toggle switch.
- Scope of delivery: M7 (cap, stainless steel tip with CCD screen and O-rings, stem, condenser), tin case, DynaTorch (unfilled).
- Variants: Besides the classic M7, there is the M7 TwoToniuM in a two-tone design (technically identical) and the M7 XL Stealth in a dark finish.
DynaVap – M7XL: more length, more relaxed handling
The M7XL is for those who like the M7 concept but want a “bigger” feel when holding and drawing. Use case: if you prefer a more relaxed grip, more distance from the heat, or simply enjoy the XL handling. The real difference is inside: the M XL Condenser Assembly offers six airflow settings through the condenser depth – and the longer path to the mouthpiece noticeably cools the vapor.
3) Premium feeling: The UniDyn & WoodWynd (for aesthetics & “favorite piece” vibes)
DynaVap – The UniDyn: clean, modern, very “straight”
The UniDyn looks extremely modern and streamlined – a setup you’ll love to have on your table. Use case: if you want a premium design that remains super practical for everyday use (and fits easily into your accessories/storage). The highlight is the one-piece UniBody made of medical titanium: tip and shaft are seamlessly connected, with a HypoTherm heat break (T-Break) in between that keeps heat away from the chamber.
- Material: medical-grade titanium with scratch-resistant DuraDyn coating, stainless steel CCD screen.
- Cap: BallR Cap with convection – not the classic Captive Cap, but the flavor-focused variant.
- Chamber: 0.1 g, reducible with Adjust-a-Bowl.
- Airflow: 7 settings via the adjustable condenser.
- Practical: grooved tip for grinding on the go · only 2 O-rings total, so extremely low maintenance · 10 mm joint for water filters.
- Contents: UniDyn (BallR Cap, titanium tip & shaft with CCD, titanium condenser with mouthpiece, 2 O-rings) and DynaVap tin box.
DynaVap – WoodWynd: wood look, warm handling, premium for everyday use
The DynaVap WoodWynd is for those who prefer a visually and tactilely "warmer" feel. It not only looks elegant but also makes handling very pleasant in everyday use. Use case: if you want a beautiful setup but still want to stay completely "daily." The stem is made of Padauk hardwood with stainless steel crowns and is hourglass-shaped – each piece has its own grain, so yours will look different from your neighbor’s.
- Material: Padauk hardwood stem with stainless steel crowns, helix titanium tip, stainless steel cap.
- Helix tip: thicker chamber walls – retain heat longer and provide more consistent draws.
- Mouthpiece: triple helix without O-rings – one less wear part.
- Water filter: fits directly and without a cone into 10mm openings.
- Important when heating: Always direct the flame at the cap, never at the wooden stem. DynaVap explicitly recommends an induction heater for the WoodWynd.
- Scope of delivery: WoodWynd (wood stem, helix tip, condenser, cap) and DynaVap tin · fits in XL-DynaStash or SlimStash.
4) For water & "smooth": VonG DynaVap (i), VonG X + starter sets
DynaVap – The VonG (i): Titanium setup for water
The The VonG (i) is for everyone who likes to use DynaVap with a water filter or generally wants a setup that feels like a "tool": robust, high-quality, very well thought out. Use case: at home with glass, if you like smooth draws. Tip, stem, and condenser are completely made of titanium, plus there is a replaceable, rotatable titanium sleeve – and the whole thing can be completely disassembled without tools.
- Material: titanium for tip, shaft, and condenser, with a rotatable titanium sleeve.
- Connection: conical mouthpiece in 10 mm and 14 mm – fits directly into female water pipe openings.
- Chamber: halved with Adjust-a-Bowl.
- Includes: cap, titanium tip with CCD screen and O-rings, titanium shaft with sleeve, standard titanium condenser – plus a free SlimStash in zebrawood.
Starter set – The VonG (i): all-in-one start for the water setup
If you don’t want to gather everything separately, the The VonG (i) starter set is extremely convenient. Use case: you want to start cleanly right away, with a coherent accessory setup and proper DynaVap storage. The DynaVap starter kit includes everything you’d usually reorder after two weeks: an empty Cyclone triple burner, a DynaStash in walnut, DynaWax for the threads, a titanium CCD screen, plus 5 high-temperature O-rings and condenser O-rings.
DynaVap – The VonG X: water use case with an "X" vibe
The The VonG X is the variant for those who want the VonG use case (water/smooth) but prefer a more "X" look and setup. Use case: if you like using DynaVap with water and want a distinctive, unique setup. Technically, it is a hybrid construction: titanium housing with a heavy stainless steel tip that stores more heat and extracts more powerfully than pure titanium.
- Material: Titanium housing + stainless steel tip, two-tone DuraDyn finish.
- Chamber: 0.1 g, halved with Adjust-a-Bowl.
- Airflow: Airport sits on the mouthpiece and is opened or closed by twisting.
- Connection: 10 mm and 14 mm cones, housing with 14 mm joint on both ends.
- Condenser: flexible – optionally connected with tip or mouthpiece.
- Variant: Also available as VonG X Stealth in a dark finish.
5) Maximum Setup: HyperDyn (if you want “big”)
The HyperDyn is the candidate for everyone who really loves DynaVap and simply wants more “presence” in their setup. Use case: at home, if you like having a powerful, solid device in your hand – including a case for clean DynaVap storage. The “big” here is literal: with a 0.25 g Big Bowl, the HyperDyn holds two and a half times an M7 and five times a G3.
- Chamber: 0.25 g – the largest in the DynaVap lineup.
- Material: medical-grade, hardened, and colored titanium with scratch-resistant DuraDyn coating.
- Cap: Hyper Cap made of titanium with captive cap technology.
- Airflow: 7 settings.
- Connection: 10 mm and 14 mm cone for water filters.
- Contents: Hyper Cap, Hyper Titanium Tip with CCD and O-rings, titanium condenser assembly with mouthpiece, HyperDyn titanium stem, dosing capsule, and metal tin.
- Modular: compatible with existing DynaVap midsections, tips, and mouthpieces.
Bonus: Starter Set The M7 Walnut (for the “complete & nice” start)
Direct comparisons: DynaVap G3 vs M7, B2 vs M7, UniDyn vs M7 & HyperDyn vs M7XL
DynaVap G3 vs M7
Whether you're searching for DynaVap G3 vs M7 or DynaVap M7 vs G3 – these are two completely different philosophies. The G3 is glass, two-piece, 0.05 g, and deliberately simple – no airflow control, no tips, no induction heater. The M7 is all metal, 0.1 g with Adjust-a-Bowl, has adjustable Airport, and can be expanded in any direction. If you love the taste of glass and need little: G3. If you want a device for the coming years: M7.
DynaVap B2 vs M7
We get this question both ways – as B2 vs M7 and as DynaVap M7 vs B2. The B2 has a silicone stem and 0.075 g chamber, the M7 is all stainless steel with 0.1 g, Finless Tip, and Airport. Both accept all Tips and induction heaters. Practically, this means: The B2 is the cheaper entry with the same ecosystem, the M7 gives you airflow control and cooler feel when heating. If you can afford the extra cost, the M7 is the device most people stick with long-term.
DynaVap UniDyn vs M7
Same chamber size (0.1 g), different design. The UniDyn is titanium instead of stainless steel, making it significantly lighter, has 7 instead of one Airport level, a BallR Cap with convection instead of the Captive Cap, and uses only two O-rings. The M7 is more robust in the sense of “indestructible” and more affordable. In short: with DynaVap M7 vs UniDyn, you choose between flavor, fine control, and weight (UniDyn) and value plus worry-free use (M7). The same basically applies to UniDyn vs M7 XL, only the XL with its 6 airflow levels comes closer to the UniDyn.
HyperDyn vs M7XL
Here the chamber decides: 0.25 g with the HyperDyn versus 0.1 g with the M7XL. The HyperDyn is the device for longer sessions and rounds of two or three, with titanium, 7 airflow levels, and a 14-mm connection. The M7XL remains the better everyday and on-the-go device. If you mostly vape alone and briefly, the HyperDyn would simply be oversized.
VonG (i) vs VonG X
Both are designed for water filtration and have 10- and 14-mm cones. The VonG (i) is all titanium – lighter, with a rotating sleeve and tool-free disassembly. The VonG X features a heavy stainless steel tip on a titanium body, extracts more powerfully, and controls airflow by rotating the mouthpiece. Titanium purist: (i). More punch per draw: X.
DynaVap model names decoded: VapCap, “The M 2021/2022,” and the components
- VapCap is DynaVap’s product name for the devices themselves – when you read “DynaVap VapCap,” it doesn’t refer to a special model.
- “The M 2020 / 2021 / 2022”: The M series was released for years as an annual model. Today’s M7 is the seventh generation of this line. So if you’re looking for DynaVap 2021, DynaVap 2022, or DynaVap M 2021, the M7 is the current successor. Because the DynaVap system is modular, accessories from older M models generally still fit – the exception is the G3 with its glass body.
- Cap: the cap that clicks. Available in several versions – Captive Cap (standard), BallR Cap (convection, built into the UniDyn), Hyper Cap, and Armored Cap.
- Tip: the part with the chamber. Determines fill amount and extraction character – e.g., Finless Tip on the M7 or Helix Tip on the WoodWynd.
- Stem: the middle part you hold – made of stainless steel, titanium, silicone, wood, or glass.
- Condenser: the tube in the stem that cools the vapor. Its depth controls airflow in many models.
- CCD: the screen at the chamber bottom that holds back your material.
- Adjust-a-Bowl: the option to reduce the chamber size by half via condenser position – microdosing without a second device.
- Stealth Variants: visually dark versions of well-known models (e.g., B2 Stealth, M7 XL Stealth, VonG X Stealth) – technically identical to the respective standard model.
DynaVap Accessories, Storage & Cleaning (to keep it tasting great)
- DynaVap Cap: The fastest way to change the character. BallR Cap for more convection and flavor, Hyper Cap and Thermal Hyper Cap for large chambers, Armored Cap for robust handling – plus the classic VapCap Caps as replacements.
- Tips: change chamber size and extraction without needing a new device.
- Dosing Capsules: pre-fill and swap on the go – available in standard and hyper variants. A HyperDyn already includes one.
- Wear Parts: CCD screens, condenser sealing rings, high-temperature O-ring kits, and titanium condensers – you should replace these once or twice a year depending on usage.
- Care Sets: DynaKit Basic and DynaKit Maintenance bundle exactly what helps with disassembly and maintenance.
- DynaVap Case & Storage: from the small SnapStash to the SlingStash and DynaBank up to the wooden DynaStash – the latter is also included in the starter sets. For everyday use as a DynaVap M7 Case, the supplied tin can also do the job.
- DynaGrynd: the suitable grinder if you want to keep the grind size consistent – with such small chambers, it makes more difference than you think.
Overview: Which DynaVap suits you?
| Model | For whom? | Chamber | Material | Price range | Short feature | Link |
|---|---|---|---|---|---|---|
|
The G3
|
Budget & "just testing" | 0.05 g | Glass UniBody | € · Entry | Only 2 parts, torch included · no induction heater | View → |
|
The B
|
Beginner, uncomplicated | no information | Stainless steel + silicone | €€ · Entry+ | Case + DynaTorch included, 10 mm cone | View → |
|
The B2
|
Beginner with upgrade desire | 0.075 g | Stainless steel + silicone | €€ · Entry+ | All tips + induction heater usable | View → |
|
M7
|
Daily driver | 0.1 g can be halved |
Stainless steel | €€€ · Mid-range | Finless Tip (−20% heat), Airport | View → |
|
M7XL
|
Daily + XL handling | 0.1 g can be halved |
Stainless steel | €€€ · Mid-range | 6 airflow levels, longer cooling path | View → |
|
The UniDyn
|
Premium, clean & modern | 0.1 g reducible |
Titanium UniBody | €€€ · Mid-range | BallR Cap, 7 airflow levels, only 2 O-rings | View → |
|
WoodWynd
|
Premium with wood vibe | Helix Tip | Padauk wood + titanium | €€€€ · Premium class | Mouthpiece without O-rings, direct 10 mm | View → |
|
The VonG (i)
|
Water setup | can be halved | Titanium complete | €€€€ · Premium class | 10 & 14 mm cone, SlimStash free | View → |
|
The VonG X
|
Water + distinctive look | 0.1 g can be halved |
Titanium + stainless steel | €€€€ · Premium class | Rotatable airport on the mouthpiece | View → |
|
HyperDyn
|
Maximum, longer sessions | 0.25 g Big bowl |
Hardened titanium | €€€€€ · Premium | Hyper Cap, 7 airflow levels, dosing capsule | View → |
|
Starter set VonG (i)
|
Water start without guessing | like VonG (i) | Titanium core | €€€€€ · Premium | Cyclone burner, DynaStash Walnut, O-Rings | View → |
|
Starter set M7 Walnut
|
Daily start "complete & beautiful" | like M7 | Stainless steel + walnut | €€€€ · Premium class | DynaStash, Lighter, DynaWax, O-Rings | View → |
Frequently Asked Questions about DynaVap
Which DynaVap is the best?
There is no single best option – but an honest ranking: cheapest entry The G3, best entry with future potential The B2, best overall package M7 / M7XL, finest control The UniDyn, for water VonG (i), for long sessions HyperDyn. If you can’t decide and want only one device: M7XL.
Do I need a special lighter?
A normal lighter is not reliable – you need a jet flame (torch) or an induction heater. The B, The B2, and M7 / M7XL come with a DynaTorch, the G3 with a Clipper torch. All torches come empty; you need to get butane separately.
How much fits in the chamber?
Depending on the model: 0.05 g for the G3, 0.075 g for the B2, 0.1 g for M7, M7XL, UniDyn, and VonG X, and 0.25 g for the HyperDyn. All models with Adjust-a-Bowl allow you to reduce the chamber to half. DynaVap does not specify a gram amount for The B – it is practically in the same range as the B2.
Does a DynaVap fit on my bong or water pipe?
Yes. The B, The B2, M7, and UniDyn have a 10 mm cone, and the WoodWynd even fits directly into 10 mm openings without a cone. VonG (i), VonG X, and HyperDyn also come with 14 mm and fit common larger joints without extra adapters.
What does “DynaVap 2021” or “The M 2022” mean?
These are the earlier annual editions of the M series – also searched as DynaVap 2020, DynaVap 2022, or DynaVap M 2022. The current M7 is the seventh generation and the latest successor. Accessories from the DynaVap system are largely cross-compatible – only the G3 stands out due to its glass body.
Can I use an induction heater?
Yes, for all metal and titanium models – it is explicitly approved for the The B2, and DynaVap even recommends it for the WoodWynd. For the G3, the manufacturer advises against it; here you should stick to the flame.
How do I properly clean my DynaVap?
Disassemble, clean metal parts with warm water and a brush, occasionally soak in isopropanol and dry well. Only briefly soak O-rings, never soak wooden parts. Details in the Accessories & Cleaning section.
Is a starter set worth it, or should I buy everything separately?
If you know you want storage, a torch, and replacement O-rings anyway, a DynaVap set is the more convenient and usually cheaper option. If you just want to test it out first, the device with the included case and torch is perfectly fine.
